DIY rolling plant caddy checklist
For making a rolling caddy for one large indoor plant pot. Select casters rated above the combined weight of the pot, soil, and plant.
What to get
Exterior-grade plywood square
1
Locking swivel casters
4
Caster mounting screws
1 pack
Drill
1
Driver bit set
1 set
Tape measure
1
Carpenter's square
1
Pencil
1
Jigsaw or circular saw
1
Medium-grit sandpaper
2 sheets
Fine-grit sandpaper
2 sheets
Water-resistant wood sealer
1 small can
Paintbrush
1
Waterproof plant saucer
1
Safety glasses
1
Who this list is for
This checklist is for building a rolling caddy for one large indoor plant pot. The locking swivel casters should be rated above the combined weight of the pot, soil, and plant.
How to use this list
Measure the pot footprint with the tape measure and mark the exterior-grade plywood square with the carpenter's square and pencil. Cut the board with a jigsaw or circular saw, wearing safety glasses, then smooth edges with medium-grit and fine-grit sandpaper. Seal the wood with water-resistant wood sealer and a paintbrush. After it dries, position and attach four locking swivel casters with the drill, driver bit set, and caster mounting screws. Set the waterproof plant saucer on top.
Common mistakes
Do not choose casters based on the empty pot alone. Avoid making the plywood square smaller than the pot or saucer. Do not install casters too close to the center or unevenly near the edges. The wood sealer is needed before regular contact with a plant saucer and indoor watering moisture.
What is on this list
The list includes an exterior-grade plywood square, four locking swivel casters, caster mounting screws, drill, and driver bit set. It also covers measuring and cutting tools, sandpaper, water-resistant wood sealer, paintbrush, waterproof plant saucer, and safety glasses. Cross off tools and supplies you own.
When you are done
Lock the casters, set the plant pot in its saucer, and check that the caddy stays level. Roll it slowly on the intended floor, then relock the casters. Inspect screws and the sealed wood periodically, especially after watering.
FAQ
Who is "DIY rolling plant caddy checklist" for?
This checklist is for building a rolling caddy for one large indoor plant pot. The locking swivel casters should be rated above the combined weight of the pot, soil, and plant.
How should I use "DIY rolling plant caddy checklist"?
Measure the pot footprint with the tape measure and mark the exterior-grade plywood square with the carpenter's square and pencil. Cut the board with a jigsaw or circular saw, wearing safety glasses, then smooth edges with medium-grit and fine-grit sandpaper. Seal the wood with water-resistant wood sealer and a paintbrush. After it dries, position and attac…
What should I skip or avoid with "DIY rolling plant caddy checklist"?
Do not choose casters based on the empty pot alone. Avoid making the plywood square smaller than the pot or saucer. Do not install casters too close to the center or unevenly near the edges. The wood sealer is needed before regular contact with a plant saucer and indoor watering moisture.
What is on the "DIY rolling plant caddy checklist" list?
The list includes an exterior-grade plywood square, four locking swivel casters, caster mounting screws, drill, and driver bit set. It also covers measuring and cutting tools, sandpaper, water-resistant wood sealer, paintbrush, waterproof plant saucer, and safety glasses. Cross off tools and supplies you own.
What should I do when I am done?
Lock the casters, set the plant pot in its saucer, and check that the caddy stays level. Roll it slowly on the intended floor, then relock the casters. Inspect screws and the sealed wood periodically, especially after watering.
Related lists
For general planning only. Valedo does not guarantee this list’s accuracy, completeness, or suitability. Verify information before relying on it. Not a substitute for professional advice or safety training.